engine won't slow down

04DmaxLLY · 07-03-2008, 08:23 PM

I have a '99 Yukon with the 5.7l 350 engine in it. It runs and drives fine until you try to stop. When you let off of the gas it is like the pedal is stuck. When you finally get stopped the engine runs like normal, but it is hard to get it to stop with the engine still trying to push you forwards. I don't know what the problem is and have never heard of this issue before. Any help would be appreciated.

Hayden · 07-04-2008, 05:58 PM

Have the idle control or throttle position sensor tested. It's a good start

z07 · 07-04-2008, 07:41 PM

Disconnect and plug off the vacuum line to the cruise module too.

04DmaxLLY · 07-04-2008, 09:38 PM

Thanks for the idea's I'd never seen or heard of this problem, before I got my Duramax I had a '96 with 13x,000 miles and never had a problem. The Yukon is my mom's daily driver and we were clueless. We looked at the idle control today, hopefully that is the problem. We cleaned it and it ran worse, so we are hoping a new one will fix the problem.

leolkfrm · 07-08-2008, 05:55 AM

try removing the throttle cable, make sure the cable moves smoothly from the pedal out, sometimes cables degrade on the inside and you can't see it, its one of the reasons drive by wire is being used

07-03-2008, 08:23 PM	#1 (permalink)
04DmaxLLY Junior Member Join Date: Jul 2008 Posts: 2	engine won't slow down I have a '99 Yukon with the 5.7l 350 engine in it. It runs and drives fine until you try to stop. When you let off of the gas it is like the pedal is stuck. When you finally get stopped the engine runs like normal, but it is hard to get it to stop with the engine still trying to push you forwards. I don't know what the problem is and have never heard of this issue before. Any help would be appreciated.

07-04-2008, 05:58 PM	#2 (permalink)
Hayden Senior Member Join Date: May 2006 Location: Bay City,Michigan Posts: 363	Have the idle control or throttle position sensor tested. It's a good start __________________ There Is No Replacement For Displacement

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
very slow starting	rambleranch@ear	GMC Truck Forum	4	05-09-2008 06:01 AM
slow acceleration	dj79	Chevy Truck Forum	7	04-26-2007 07:36 PM
slow acceleration still	dj79	Chevy Truck Forum	3	03-26-2007 12:46 PM
Slow day here	chevyguy	Off-Topic	7	11-05-2005 04:02 PM

07-04-2008, 07:41 PM	#3 (permalink)
z07 Senior Member Join Date: Feb 2008 Posts: 172	Disconnect and plug off the vacuum line to the cruise module too.

07-04-2008, 09:38 PM	#4 (permalink)
04DmaxLLY Junior Member Join Date: Jul 2008 Posts: 2	Thanks for the idea's I'd never seen or heard of this problem, before I got my Duramax I had a '96 with 13x,000 miles and never had a problem. The Yukon is my mom's daily driver and we were clueless. We looked at the idle control today, hopefully that is the problem. We cleaned it and it ran worse, so we are hoping a new one will fix the problem.

07-08-2008, 05:55 AM	#5 (permalink)
leolkfrm Senior Member Join Date: Mar 2008 Location: N.Y. Posts: 461	try removing the throttle cable, make sure the cable moves smoothly from the pedal out, sometimes cables degrade on the inside and you can't see it, its one of the reasons drive by wire is being used