body damage

smeier89 · 01-29-2009, 04:11 PM

i have a 93 toyota pickup. someone thought it was nice to put a dent in the driver door. its rather large and i was wondering how to fix this to make the best fix.
any comments would be helpful. thanks!

peterbilt · 01-29-2009, 05:03 PM

tap and dolley set.

Kennyray · 01-29-2009, 06:24 PM

Might try a plunger first, sometime it will pull a lot of it out if its not creased to bad. Won't cost anything to try.

Blackwolf14804 · 01-29-2009, 07:57 PM

Try pulling off the inner door panel and push the dent out. Sometimes you can push quite a bit if not all of it out just using your hand

smeier89 · 01-30-2009, 04:22 PM

ok thanks everyone ill give it a try

batty1214 · 01-30-2009, 07:46 PM

if you cannot push out the dent from the inside, you might use a car innertube, wedge it into the door and start to slowly inflate it..... I do it at work to the trucks.... and it works pretty well...... just avoid sharp stuff.... or it'll scare you

01-29-2009, 04:11 PM	#1
smeier89 Full Member Join Date: Jan 2009 Posts: 11	body damage i have a 93 toyota pickup. someone thought it was nice to put a dent in the driver door. its rather large and i was wondering how to fix this to make the best fix. any comments would be helpful. thanks!

01-29-2009, 05:03 PM	#2
peterbilt Senior Member Join Date: May 2007 Location: Florida Posts: 1,904	tap and dolley set. __________________ ~Eric~

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
bent control arm bracket/frame damage how can i fix it	shaunweldin	Dodge Truck Forum	0	06-03-2008 01:24 PM
What cause damage to my 350 Chev?	tgzzzz	Chevy Truck Forum	13	05-30-2008 11:44 AM
Body Damage Questions	Ryan2000ak	Chevy Truck Forum	4	03-07-2007 10:30 PM
Truck strike will damage business, says port official (Canada.com)	trucknews	Truck News (headlines)	0	06-27-2005 05:30 AM
Rainfall causes damage to new park trail (The Ohio University Post)	trucknews	Truck News (headlines)	0	04-26-2005 09:30 AM

01-29-2009, 06:24 PM	#3
Kennyray Senior Member Join Date: Oct 2005 Location: Birmingham, AL Posts: 632	Might try a plunger first, sometime it will pull a lot of it out if its not creased to bad. Won't cost anything to try.

01-29-2009, 07:57 PM	#4
Blackwolf14804 Senior Member Join Date: May 2007 Location: Almond, NY Posts: 87	Try pulling off the inner door panel and push the dent out. Sometimes you can push quite a bit if not all of it out just using your hand

01-30-2009, 04:22 PM	#5
smeier89 Full Member Join Date: Jan 2009 Posts: 11	ok thanks everyone ill give it a try

01-30-2009, 07:46 PM	#6
batty1214 Senior Member Join Date: Nov 2008 Location: Vernal Utah Posts: 1,127	if you cannot push out the dent from the inside, you might use a car innertube, wedge it into the door and start to slowly inflate it..... I do it at work to the trucks.... and it works pretty well...... just avoid sharp stuff.... or it'll scare you